A326018A (B) MR1 (EN)
Three layers of Gyproc SoundBloc 15mm one side and two inner layers of Gyproc SoundBloc 15mm and an outer layer of Gyproc SoundBloc MR 15mm fixed to outside faces of two Gypframe 92 S 10 ‘C’ Stud frameworks with studs at 600mm centres, cross braced using Gypframe 99 FC 50 Fixing Channel at 3600mm centres. Three layers of 100mm Isover Cladding Roll 40 and two layers of 100mm stone mineral wool (min. 62kg/m3) in the cavity. For heights up to 8000mm.
Fire Integrity (mins)
Fire Insulation (mins)
Sound Insulation (Airborne) Rw (dB)
Sound Insulation (Airborne) Rw + Ctr (dB)
Maximum Height (mm)
Partition Thickness (mm)
A326018A (B) MR1 (EN)
|StandardsBS EN ISO 140-3,Acoustics - Measurement of sound insulation in buildings and of building elements. Laboratory measurement of airborne sound insulation of building elements.||Standard types|
|StandardsBS 5234-2,Specification for performance requirements for strength and robustness including methods of test.||Standard types|
|StandardsBS EN 1364-1,Fire resistance tests for non-loadbearing elements - Walls.||Standard types|
This section should be read in conjunction with the Products list.
- Abutment Fixing: Two rows of Gypframe 'C' stud suitably fixed to structure at 600mm centres in two lines staggered by 300mm.
- Bracing Centres: Cross bracing half staggered between adjacent stud pairs and fixed to each stud with four wafer head screws.
- Bracing Centres (mm): 3600 mm
- Base Channel Fixing: Two rows of Gypframe channel suitably fixed to floor at 600mm centres in two lines staggered by 300mm.
- Deflection Allowance: Vertical deflection only. To be determined by a Structural Engineer.
- Dropped Soffit: For principles of deflection head construction refer to detail ST-127-Z1L3-09
- Finishing Requirements: To achieve the specified performances, the system should be finished using either one of our Thistle or ThistlePro plasters, or Gyproc jointing products. See the product range guides on the British Gypsum website for more information. For further guidance on skimming moisture resistant grade boards see the White Book - Finishes section.
- Fixing Strap: Used to support horizontal board joints in face layer of multiple layer board linings and enable board screw fixing at 300mm centres.
- Loadbearing: No
- Maximum Height: The maximum heights quoted are limited by the fire state field of application or by limiting deflection of L/240 at 200 Pa, whichever is the lower of the two.
- Other Requirements: SpecSure® system performance warranty confirms that British Gypsum proprietary systems will perform as specified for the lifetime of the building. The SpecSure® warranty requires that all components are specified in full and constructed in accordance with British Gypsum’s installation guidance. For more details see the British Gypsum website. Always check with the design team before making any changes to the chosen specification, ensuring appropriate substantiation is sought to confirm that the solution still meets all required project performances.
- Screw: Board layer 1 (inner) and board layer 2, fix securely to Gypframe metal supports around the perimeter of the board at maximum 300mm centres; Board layer 3 (outer), fix securely to all Gypframe metal supports around the perimeter of the board and intermediate stud positions at maximum 300mm centres. External corners reduce fixings to 200mm. Drywall screws can be used for fixing boards to metal profiles with a thickness of 0.8mm or less. All joints staggered between layers. Fix working from the centre of each board. Position screws not less than 13mm from cut edges and 10mm from bound edges of boards. Set screw heads flush with plasterboard surface; do not break paper or gypsum core.
- Sealant: Locate sealant at junctions with adjoining structure and other air paths. Apply as a continuous bead to clean, dry, dust-free surfaces, leaving no gaps. After application of sealant, bulk fill gaps between floor and underside of plasterboard using Gyproc joint compound.
- Stud: Two rows of Gypframe studs arranged in pairs.
- Stud Centres (mm): 600 mm
- Approx. Weight (kg/m2): 80 kg/m²
- Head Channel Fixing: Two rows of Gypframe channel suitably fixed to soffit at 600mm centres in two lines staggered by 300mm.
Need CAD, BIM, Test Reports and Technical Specifications?
Log in to access CAD .dwg files.
Log in and add a System Specification to a Project to access BIM files, Test Reports, and Technical Specification files.
Please add this Specification to a project and go to that Project to access the related Test Reports.
|Test report label||Test report name|
|Test report labelFire Resistance Test Report||Test report nameBTC 21613F|
|Test report labelSound Insulation Test Report||Test report nameBTC 13565A|
|Test report labelPartition Duty Test Report||Test report nameBTC 152LC|
A unique warranty that confirms British Gypsum proprietary systems will perform as specified for the lifetime of the building.